HumiSeal 1A33 LOS Description
- HumiSeal 1A33 LOS is a single component, polyurethane conformal coating, suitable for general printed circuit board applications.
- It is a development of HumiSeal 1A33 with reduced odor levels and lower toxicity solvents.
- After complete cure, the properties of HumiSeal 1A33 LOS and HumiSeal 1A33 are comparable.
- This contains no free isocyanates and will fluoresce under UV light for inspection purposes.
- 1A33 LOS is compliant with RoHS Directive 2015/863/EU and China RoHS 2.
Technical data of HumiSeal 1A33 LOS
Property | Value |
---|---|
Density, per ASTM D1475 | 0.92 ± 0.02 g/cm³ |
Solids Content, % by weight per Fed-Std-141, Meth. 4044 | 44 ± 2 % |
Viscosity, per Fed-Std-141, Meth. 4287 | 195 ± 65 centipoise |
VOC | 512 grams/litre |
Recommended Coating Thickness | 25 - 75 microns |
Drying Time to Handle per Fed-Std-141, Meth. 4061 | 30 minutes |
Optional Curing Conditions to Reach Optimum Properties | 30 days at RT |
30 hours @ 76°C | |
20 hours @ 88°C | |
Recommended Thinner | HumiSeal® Thinner 905 |
Recommended Stripper | HumiSeal® Stripper 1063 |
Shelf Life at Room Temperature, DOM | 24 months |
Thermal Shock, 50 cycles per MIL-I-46058C | -65°C to 125°C |
Coefficient of Thermal Expansion - TMA | 193 ppm/°C |
Glass Transition Temperature - DSC | 26°C |
Modulus - DMA | 27.2 MPa |
Flammability, per UL 94 | Pending |
Dielectric Withstand Voltage, per MIL-I-46058C | >1500 volts |
Insulation Resistance, per MIL-I-46058C | 2.0 x 10^14 ohms (200TΩ) |
Moisture Insulation Resistance, per MIL-I-46058C | 1.6 x 10^10 ohms (16GΩ) |
Application of HumiSeal 1A33 LOS
Conformal coatings can be successfully applied to substrates that have been cleaned prior to coating and to substrates assembled with low residue, “no clean” assembly materials. Users should perform adequate testing to confirm compatibility between the conformal coating and their particular assembly, materials, process conditions and cleanliness levels.
HumiSeal 1A33 LOS Pre-Blends are available, diluted to a specific viscosity for immediate use. No additional dilution is required. Customers should establish which Pre-Blend is suitable for their equipment and application method before commercial use.
Dipping
- A controlled rate of immersion and withdrawal (5-15 cm/min) will further ensure even deposition of the coating and ultimately a uniform film.
- During the application, evaporation of solvent causes an increase in viscosity that should be adjusted by adding small amounts of Thinner.
- Viscosity in the dip tank should be checked regularly, using a simple measuring device such as a Zahn or Ford viscosity cup.
Spraying
- HumiSeal 1A33 LOS Pre-Blends are available which can be sprayed using conventional spraying equipment.
- Spraying should be done in an environment with adequate ventilation so that the vapour and mist are carried away the operator.
- The specific pre-blend and spray pressure will depend on the specific type of spray equipment used and operator technique.
Brushing
- HumiSeal 1A33LOS Pre-Blends are available which may be brushed onto surfaces.
- Uniformity of the film depends on specific pre-blend chosen and operator technique.
HumiSeal 1A33 LOS Application notes
Storage
- HumiSeal 1A33LOS and Pre-Blends should be stored away excessive heat or cold, in tightly closed containers.
- HumiSeal products may be stored at temperatures of 0 to 35°C.
- Prior to use, allow the product to equilibrate for 24 hours at a room temperature of 18 to 32°C.
Caution
Application of HumiSeal Conformal Coatings should be carried out in accordance with Local and National Health and Safety regulations.
- The solvents in HumiSeal 1A33 L O S and its Pre-Blends are flammable.
- Material should not be used in presence of open flame or sparks.
- Use only in well-ventilated areas to avoid inhalation of vapours or spray.
- Avoid contact with skin and eyes.
Where to buy genuine HumiSeal 1A33 LOS ?
Hicotech is an authorized distributor of Humiseal in Vietnam, and we have earned the trust of reputable clients such as Vinfast, Ford, Panasonic, and more. Contact us now for consultation and to get the best price for HumiSeal 1A33 LOS.
In addition, we also distribute other product categories such as:
- Industrial chemicals
- Cleaning Chemicals
- Encapsulants
- SMT equipment
- Conformal coatings
- Industrial Accessories
All of our products come with a guarantee of being genuine, with complete documentation proving their origin and quality. This ensures that customers receive high-quality products that meet international standards.
Contact information:
Hotline/Zalo: 094 526 1931
Website: Hicotech.com.vn
Email: Sale@hicotech.com.vn
Có 0 bình luận, đánh giá về HumiSeal 1A33 LOS
TVQuản trị viênQuản trị viên